220V 30W Power Led Board Module IP65 2800-3200K Warm White

The 30 W AC-LED module integrates a COB LED with a Smart IC constant-current driver on an aluminum PCB, enabling direct AC220–240 V mains operation—no external LED driver required. Designed for both electronics hobbyists and engineering applications, it’s ideal for DIY lighting builds, fixture repairs, and rapid prototyping where compact, driverless illumination is preferred.

✨ Key Features

• Direct AC Mains Input (AC220–240 V) 🔌 — Plug-and-light module; no separate LED driver needed.
• Warm White 2800–3200 K 🌟 — Comfortable, incandescent-like tone for general lighting.
• High CRI (Ra ≥ 80) 🎨 — More accurate color rendering for better visual quality.
• Wide 270° Beam 🔆 — Broad area illumination from a compact form factor.
• IP65 Rated 🛡️ — Dust-tight and protected against water jets when properly installed.
• Aluminum Core PCB 🧊 — Efficient heat spreading; pair with a suitable heatsink for longevity.
• Long Service Life ⏱️ — Up to 30,000 hours with adequate thermal management.
• COB + SMD Smart IC 🧠 — Integrated constant-current regulation for stable output.

📊 Technical Specifications

• Power: 30 W
• Input Voltage: AC220–240 V (220 V / 230 V / 240 V)
• LED Technology: COB with SMD Smart IC driver
• Color Rendering Index (CRI): Ra80
• Correlated Color Temperature (CCT): Warm White 2800–3200 K
• Beam Angle: 270°
• Lifespan: 30,000 hours (with good heatsink)
• Ingress Protection: IP65
• Substrate / Housing Material: Aluminum

🔧 Installation & Thermal Guidelines

• Heatsinking required: Mount the module to a suitable heatsink using thermal paste or a thermal pad and secure it mechanically for optimal heat transfer.
• Wiring: Connect to AC Line (L) and Neutral (N) with properly rated, insulated conductors; secure strain relief on leads.
• IP65 practices: Maintain sealing around terminals and mounting points to preserve ingress protection; avoid immersion.
• Enclosure: Use a ventilated, electrically insulated enclosure when possible to prevent accidental contact with live parts.

🤖 For Makers: Control & Integration Tips

While this module runs directly from mains voltage, it can be switched or automated in projects with Arduino, Raspberry Pi, or other microcontrollers using appropriate isolation:

• Use a relay, solid-state relay (SSR), or triac-based AC module rated for the load and voltage.
• Do not connect mains or this module directly to a microcontroller. Maintain galvanic isolation at all times.
• Dimming is not guaranteed; only use compatible AC dimmers if specified by your control hardware and test carefully.

🧪 Applications

• DIY and hobby lighting projects
• Repair or retrofit of faulty light fixtures
• Workbench/task lighting and utility luminaires
• Prototyping with electronics components and lighting modules

⚠️ Safety Information

• High voltage hazard: Operates at AC220–240 V. Only qualified persons should install. Disconnect power before handling.
• Insulation: Ensure proper electrical insulation, secure terminations, and strain relief. Prevent any short circuits.
• Moisture caution: Despite IP65, improper installation or exposed terminals can allow water ingress. Keep the unit dry during wiring and avoid liquid contact.
• Thermal safety: Always use an adequate heatsink; excessive temperature will shorten lifespan.

📦 Package Contents

• 1 × 220V 30W Power LED Board Module, IP65, Warm White 2800–3200 K

This driverless AC-LED board is a practical choice for engineers and makers seeking a compact, high-output lighting module compatible with automation via isolated control from Arduino, Raspberry Pi, or similar microcontroller platforms. Integrate it thoughtfully with proper isolation, thermal design, and compliance with local electrical codes.